In numerous pulverization mode, Jet Mill of Glass Slag has become one of the most mainstream pulverization techniques with a small particle size, narrow particle size distribution, high purity, high particulate activity, and good dispersibility. In particular Applicable materials such as crushing drugs such as contaminated materials.
In terms of airflow milling, it is important to understand its operational rules, which is very important because only familiarize the procedure, can operate correctly.
1. The operation rules of Jet Mill of Glass Slag are as follows: Prepare materials before the start of the production order before the start of the production order. Complete the site to clean the grocery. Check whether the transportation pipes and auxiliary equipment, whether the pipelines are blocked, leak or poor sealing, whether the auxiliary equipment is intact, whether it works normally. Whether there is a phenomenon that the material is accumulated in the outer casing and the separator, if the accumulated material is required. Whether the bearing is lubricated, whether it is lubricated in an appropriate place. Check if all pipes, fastening bolts, washers, spindles, and instruments are intact, normal and flexible.
Second, Jet Mill of Glass SLAG starts the motor, control the current and time at starting, so that the device can start operation. When the equipment is operating normally, the feed speed can be adjusted according to the properties of the material. Uniform continuous feed should not be large or small, thereby affecting the separation effect of the grinding machine, making the machine easily malfunction. During operation, if an abnormality occurs, stop checking immediately before the failure continues.
Third, the main procedures of the closure and inspection of Jet Mill of Glass SLAG are as follows: After the material in the grinding machine housing is completely pulverized, it should stop the input and turn off the motor. After the machine is idling for 3 minutes, press the stop button to stop the machine. When the machine is completely stopped, open the check door and check the wear of the vessel. Fill in the corresponding production record, update the device status flag, which is convenient for the next use.
The working principle of Jet Mill of Glass SLAG is a complete crushing system composed of crushers and cyclone separators, dust collectors and air blowers. After the compressed air is filtered, the high-speed nozzle is sprayed into the crushing chamber, and the material is pulverized by repeated collision, friction and shearing at the intersection of the multi-high pressure airflow. The crushing material moves together with the rising airflow to the classified area with the suction of the fan. Under the action of centrifugation, the thickness of the material is separated, and the graded cyclone is required to grade the cyclone to enter the cyclone dust collector, and the coarse comminution continues to be pulverized down. Suitable for dry crushing of various materials that are less than 9 in the Moh, especially for high hardness, high purity, high value-added crushing materials. It includes a vertical hierarchy device. The size of the product can be adjusted between D97: 8 and 150 microns, with a good particle shape and a narrow particle size distribution. Low temperature without media crushing. specialDon't apply to thermal sensitivity, low melting point, sugar-containing and volatile substances. The grinding process is mainly dependent on the collision of the material itself, and is different from the impact of the mechanical crushing blade or the hammer on the ground on the ground, so the equipment is high, and the product is purity.
Ultra-micro Jet Mill of Glass Slag's correct usage:
2, after the pulverizer is installed, check the fastening of the fasteners of each part, if there is loose to tighten. At the same time, check if the leather belt looseness is appropriate.
3 Whether the power machine and the pulverizing machine are lubricated. 4, do not casually replace the pulley to prevent the transition chamber to produce explosion, or the speed is too low to affect the work efficiency of the pulverizer.
5
6. At any time, you should pay attention to the operation of the pulverizer, and the feed should be evenly charged to prevent blocking, do not have a long time overload. If there is found that vibration, noise, the bearing and the body temperature is too high, the outer spray, etc., should be closed immediately, and the fault can be eliminated.
ALPA Hardstone Powder Jet Mill of Glass Slag Case Sharing:
A gypsum company is a set of stone cream exploits, calcium sulfate powder, production, sales, exports for integrated enterprises, company Products are widely used in building materials, molds, food, medicine, rubber, plastics, coatings and other industries.
The company adopts advanced modern production equipment and leading production technology, natural gypsum, natural plaster powder, desulfurized gypsum powder variety, high grade, quality, and export to all parts of the country, partially exported to Japan, South Korea, South Africa , Egypt and other countries are favored by users.
Hour Yield: 3-6T
If you still have questions, you can directly contact ALPA Technology Co., Ltd. Consulting, warmly welcome the majority of users Come to consult, our company equipment is manufactured, the size is complete, there is a suitable for you!
