Environmentally-friendly Air Classifier of Graphene has gradually become the market leading to mechanical equipment, and the modern new mechanical equipment in the machinery and manufacturing industries in the stage has gradually replaced traditional rough mechanical processing and production. It became a new leading leading to the implementation of technological innovation upgrades at this stage.
In terms of airflow milling, it is important to understand its operational rules, which is very important because only familiarize the procedure, can operate correctly.
1. The operation rules of Air Classifier of Graphene are as follows: After the preparation before the boot receives the production order, prepare the material. Complete the site to clean the grocery. Check whether the transportation pipes and auxiliary equipment, whether the pipelines are blocked, leak or poor sealing, whether the auxiliary equipment is intact, whether it works normally. Whether there is a phenomenon that the material is accumulated in the outer casing and the separator, if the accumulated material is required. Whether the bearing is lubricated, whether it is lubricated in an appropriate place. Check if all pipes, fastening bolts, washers, spindles, and instruments are intact, normal and flexible.
Second, Air Classifier of Graphene starts the motor, control the current and time at starting, so that the device can start running. When the equipment is operating normally, the feed speed can be adjusted according to the properties of the material. Uniform continuous feed should not be large or small, thereby affecting the separation effect of the grinding machine, making the machine easily malfunction. During operation, if an abnormality occurs, stop checking immediately before the failure continues.
Third, the main procedures of the closure and inspection of Air Classifier of Graphene are as follows: After the material in the grinding machine housing is completely pulverized, the feed should be stopped and the motor should be closed. After the machine is idling for 3 minutes, press the stop button to stop the machine. When the machine is completely stopped, open the check door and check the wear of the vessel. Fill in the corresponding production record, update the device status flag, which is convenient for the next use.
The principle of Air Classifier of Graphene is to use the relative movement between the active gear disc and the fixed tooth disc, and obtain the material to teeth impact, friction, and materials from each other; impact. The combined material is automatically entered into the prenatal bag through the effect of rotating centrifugal force, and the dust is filtered by the vacuum cleaner. Our constellation machine's crusher is designed according to the \"GMP\" standard, all of which are manufactured in stainless steel materials, and there is no dust in the production process. And can improve the utilization rate of materials, reduce the cost of enterprise, and have reached a high level of professionalism.
Air Classifier of Graphene Job Safety Application Basic Requirements
2, pulverizer and power unit should be installed firmly. If the equipment is fixed for a long time, it should be fixed on the cement; if the device is a mobile operation, the unit should be installed on the base made of angle iron, and ensure that the belt wheel groove of the power machine (diesel or electric motor) and the equipment is in the same Rotary plane.
At the same time, check if the leather belt looseness is appropriate. 4 Whether the power machine and the pulverizing machine are lubricated.
5, don't just replace the pulley, prevent the transition chamber to produce explosion, or the speed of the pulverizer is too low.
6. After the pulverizer starts, it should be idled by 2 to 3 minutes, no abnormal phenomenon, then press the work.
7. At any time, pay attention to the operation of the equipment, the feeding should be uniform, to prevent blocking bullies, do not have a long time overload. If there is found that vibration, noise, the bearing and the body temperature is too high, the outer spray, etc., should be closed immediately, and the fault can be eliminated.
8. When blocking occurs, it should be stopped immediately. It is strictly forbidden to use a wooden stick or hand to feed or pull out the feed to avoid the pulverizer to wound the arm or damage the machine.
9. If you crush a hard raw material, the operator must wear glasses.
10, the workplace should have a ventilator and strictly prohibit fireworks to prevent dust explosion from fire.
ALPA Ceramic Powder Air Classifier Of Graphene Case Sharing: This customer is a mechanical equipment company, mainly engaged in drying, granulation, mixing equipment production and sales, the company's technical force is strong, and is intensive High-tech enterprises integrating knowledge integration.
The customer lacks experience in powder grading, but many ultrafine powder is currently required to select ultrafine powder for ultrafine powder. The customer has chosen our ALPA as a partner after investigation. Provide a grading machine device for its customers' ceramic powder production lines.
As a crusher manufacturing large enterprise, Shandong ALPA has been working to provide customers with greater value, the fineness, production capacity and installation site of each project is important information for custom selection, pre-sales service session.
Shandong Alpa as a 20-year powder engineering equipment factoryHome, there are more than 3,000 customers at home and abroad, rich research and development production experience has always led the front end of the industry, so before consulting, you need to provide the characteristics of the crushing material, the granular parameters, production production range, purity requirements, specific process requirements(Anti-high temperature, explosion-proof, anti-dust pollution, etc.), professional engineers provide appropriate equipment models or system solutions according to this information.Welcome to inquire.
