With the demand for social development and life, the demand for Steam Jet Mill for TizApyrimidine is increasing, and the requirements for fineness, purity and pass rate are increasing. In the current market, there is a great development space.
What is the design structure of Steam Jet Mill for TizApyrimidine?
Under the action of the high-speed rotary impeller, the gas pressure flowing through the impeller increases, and the high pressure airflow flows out of the impeller, the fine particles are ejected. Since the blade of the rotary vane is designed as a bending, the inlet is large, the exit cross-sectional area is small, so the airflow pressure at the outlet is reduced, the speed increases, and the rotational flow is conducive to classification.
The grading point adjustment mechanism sets three adjustment rods and keeps its synchronous motion using the chain. When the adjustment rod moves up, the fine powder increases; when the adjustment rod moves down, the fine powder is reduced. The grading point can be continuously adjusted, and the granularity of Steam Jet Mill for TizApyrimidine can be adjusted steplessly. The gradular weight product can reach D97 ≤ 3 ≤ 150 microns, which is suitable for fine grading of dry micro-micro products.
The setting of the control ring is to ensure that the control ring is formed between the control ring and the radial particles ring, and the stability of the airflow flow is controlled. The residual windlet inevitably introduces excess gas from the dry material, the temperature of the classification chamber is high, and the air can expand, and therefore designed a residual tightening to maintain the stability and balance of the graded indoor airflow.
In the conventional dispersion pulverization process, it is difficult to overcome the phenomenon of heating, viscology. The machine uses a swirling high-speed rotational movement to produce a strong airflow in the mill. The material enters the crushing room under the negative pressure of the feed port. The vortex vibration generated by the strong gas flow between the blade and the module is generated by impact, shearing and grinding. The heat of the crushing room is taken away by the airflow, and the heat generated during the crushing process does not accumulate. The finished powder from the screen stream, improves the weight of the mill can be adjusted by the screen production efficiency, and the fineness is uniform.
Steam Jet Mill for TizApyrimidine Job Safety Application Basic Requirements
2, pulverizer and power unit should be installed firmly. If the equipment is fixed for a long time, it should be fixed on the cement; if the device is a mobile operation, the unit should be installed on the base made of angle iron, and ensure that the belt wheel groove of the power machine (diesel or electric motor) and the equipment is in the same Rotary plane.
3, after the equipment is installed, check the fastening of the fasteners of each part, if there is loose to tighten. At the same time, check if the leather belt looseness is appropriate. 4 Whether the power machine and the pulverizing machine are lubricated.
5, don't just replace the pulley, prevent the transition chamber to produce explosion, or the speed of the pulverizer is too low.
6. After the pulverizer starts, it should be idled by 2 to 3 minutes, no abnormal phenomenon, then press the work.
7. At any time, pay attention to the operation of the equipment, the feeding should be uniform, to prevent blocking bullies, do not have a long time overload. If there is found that vibration, noise, the bearing and the body temperature is too high, the outer spray, etc., should be closed immediately, and the fault can be eliminated.
8. When blocking occurs, it should be stopped immediately. It is strictly forbidden to use a wooden stick or hand to feed or pull out the feed to avoid the pulverizer to wound the arm or damage the machine.
9. If you crush a hard raw material, the operator must wear glasses.
10, the workplace should have a ventilator and strictly prohibit fireworks to prevent dust explosion from fire.
AlPA Composite Powder Steam Jet Mill for Tiz Arimidine Case Sharing: This customer is a cement manufacturer, wants to deliver the cement filler composite powder, select the composite powder of the appropriate particle size section, thus Enhance the performance of the cement. Investigate the domestic powder equipment manufacturer, and finally chose our AlPA classifier to achieve the pursuit of large capacity, and ensure the particle size of the powder.
Case parameters:
Hour Yield: 25T
For powder production companies, customized production, non-standard customized products are an advantage . The demand for each company is different. Therefore, the non-standard custom of powder equipment has gave birth to the powder equipment, and the ALPA of Shandong is a powder equipment non-standard custom enterprise. Our crushing equipment customized for Taiwan companies is a good case. Enterprises that have powder equipment customization needs to contact us.
Shandong AlPa is a 20-year experience manufacturing company with Steam Jet Mill for Tiz Apyrimidine equipment, with a number of patents, welcome to inquire!
