Air Classifier Mill for AzoDicarbonamide is an industrial equipment. With the development of society and the needs of people's lives, the demand for various fine powder is increasingly demanding in the development of people's lives. It is increasingly high, and the application of classification machine is also more extensive.
In terms of airflow milling, it is important to understand its operational rules, which is very important because only familiarize the procedure, can operate correctly.
1. The operation rules for Air Classifier Mill for Azodicarbonamide are as follows: After the preparation before the boot is received, it is prepared after the production order is received. Complete the site to clean the grocery. Check whether the transportation pipes and auxiliary equipment, whether the pipelines are blocked, leak or poor sealing, whether the auxiliary equipment is intact, whether it works normally. Whether there is a phenomenon that the material is accumulated in the outer casing and the separator, if the accumulated material is required. Whether the bearing is lubricated, whether it is lubricated in an appropriate place. Check if all pipes, fastening bolts, washers, spindles, and instruments are intact, normal and flexible.
Second, Air Classifier Mill for AzoDicarbonamide starts the motor, control the current and time at starting, so that the device can start. When the equipment is operating normally, the feed speed can be adjusted according to the properties of the material. Uniform continuous feed should not be large or small, thereby affecting the separation effect of the grinding machine, making the machine easily malfunction. During operation, if an abnormality occurs, stop checking immediately before the failure continues.
Third, the main procedures for the closure and inspection of Air Classifier Mill for Azodicarbonamide are as follows: After the material in the grinding machine housing is completely pulverized, it should stop the feed and turn off the motor. After the machine is idling for 3 minutes, press the stop button to stop the machine. When the machine is completely stopped, open the check door and check the wear of the vessel. Fill in the corresponding production record, update the device status flag, which is convenient for the next use.
What is the grading principle and process of Air Classifier Mill for Azodicarbonamide? Below, below share.
1. Open the switch in the control cabinet, start the power supply, equipment operation;
2, the raw material enters the feeder
4, the raw material reaches the hierarchical body after special dispersion, grading through physical effects such as airflow and gravity;
5, the airflow of the three flow paths has the control valve group adjustment to maintain their respective balance;
6, grading The thick Chinese product is backRecycling separately;
7, clean air is discharged into the atmosphere.
For the long-term \"health\" of the equipment, we need to take some steps to protect them again.
1. First, the gap of the hammer screen can be adjusted: the friction on the screen changes varies from the distance between the material and the screen, and the friction is different. Improve the hammer speed and hammer material efficiency by adjusting the hammer net gap. However, during the production process, the screens they use are different, the raw materials are different, the hammer screening gap needs to be adjusted; in the crusher, the crusher is not very good at the beginning, but after a period of time Work, the particles inside the crusher also changes; in the grinding machine parts, the hammer head is easily worn, and the gap between the hammer head and the screen is increased, and the yield is also declining, it is difficult to maintain.
Of course, in order to test the yield of a crusher, for some of the raw materials, for some screen holes, in order to determine the appropriate hammer sieve gap and suction, the useful life of the screen and the hammer can be obtained in a short time. Very high grinding efficiency data. However, in the production of feed grinding, such specific measurement data, according to the operator's work experience, the technical content of the crusher itself is two things. People with enrichment of experience and labor experience also require higher operating costs. When the hammer is worn, the gap between the hammer and the sieve increases, the friction is reduced, and the abrasive efficiency is lowered.
2.Air Classifier Mill for AzoDicarbonamide mainly requires a reasonable use of reverse glitch: mainly to rush the side hair of the screen into the inside, greatly increase the friction, but this method is not used for a long time. After the globi polishing, the efficiency is lowered. It lasts for 30 minutes to 1 hour.
For any of the equipment, daily maintenance can be performed in order to ensure that the equipment can run for a long time, so daily is critical to the maintenance of Air Classifier Mill for Azodicarbonamide.
ALPA composite, molten silicon micro powder Air Classifier Mill for Azodicarbonamide case share:
A silicon micropowder is an earlier manufacturer of silicon micropowder production, the company has strong technical strength, advanced Inspection instruments, perfect pre-sales, sale and after-sales service, can provide high-quality crystalline silicon powder, high-purely molten silicon powder, high white ultra-fine silicon powder, etc.Taste.The company is committed to providing advantageous solutions and services for other functional applications such as electronic materials, special ceramics.
case parameters:
Product particle size: D100: 15UM
Hours Yield: 300kg
Shan dong alpa production of various types of crushers, can be powdered in medicinal materials, ingredients, chemicals, etc., the highest effect is up toWan.Our products are non-standardized products, which will customize their products according to your needs, and make a reasonable offer according to the product.
