We all know that Air Classifier Mill for Silicon Metal is a strong airflow pulverized equipment. Many stubborn hard materials will be cut into a uniform block of pulverization,
AIR The main advantage of Classifier Mill for Silicon Metal is to change the linear and surface impact grinding of conventional grinding machines to space three-dimensional impact grinding, and take advantage of high-speed airflow generated by jet in the material flow of the pulverizer to make the crushing area to produce a similar stream. The gas-solid pulverization and grading circulating flow effects of the state of state, improve the efficiency of impact crushing and energy integrated utilization.
The high-speed airflow generated by the jet impact can be fully utilized to the material flow of the pulling chamber than the other conventional methods. The average energy consumption is reduced by 30% to 40%. Since the impact-crushing area and the gas-solid flow zone are placed in the intermediate space of the pulverized chamber, the impact corrosion of high-speed airflow driven materials is improving, and the jet impact grinding process is improved. The most severe wear problem greatly reduces the possibility of material pollution, using high purity nitrogen, argon and other protective gas as a working medium, prevent oxidation, low-loop operating gas consumption, low cost. During the fully closed-loop operation, no dust is flying, and there is no contamination of the environment, and it is unharitten about the human body.
Air Classifier Mill for Silicon Metal works with high-speed rotating hammers hit materials, crushing the decision surface, the obedient surface and the natural gap. The material sent to the crusher was shocked by the rotor, and the rotor rotated around the central axis at a speed of 25 to 40 m / sec and was broken first. The material then obtains the energy disc from the rotor, flying on the hard wall at high speed, and performs secondary comminution.
Air Classifier Mill for Silicon Metal is widely used, do you know how to use it correctly? The following content hopes to help you.
1. Preparation before departure. Check if the host, connector, pipeline, and the valve are normal, working properly.
2, open the machine
(1) Open the compressor power supply, the dust collector pressure valve and the main air valve, open the air pulverizer power switch, and turn on the power switch.
(2) From zero, gradually adjust to the specified speed.
(3) Open the fan, cyclone separator, dust collector, charge motor, open the total power box, set the inverter frequency, and then start charging.
(4) The particle size of the finished product can be adjusted according to the frequency and bearing capacity of the grading wheel.
3, the sequence of stops is:
inverter-feeder-main air valve-compressor-grade impeller-motor cyclone material, dust removal switch-fan-main power supply-Air compressor.
4, Maintenance
(1) The motor should be lubricated regularly, but the lubricating oil should not excessively avoid the bearing temperature.
(2) Check the wear of impeller, helical conveyors, and crushing nozzles.
(3) After pulverizing the material, the rubber powder should be removed to avoid clogging, thereby affecting the crushing effect.
(4) After the filter bag, it should be cleaned or replaced.
5. Precautions
(1) When the discharge equipment is run, the unloading port cannot be reached, and the accident occurs.
(2) The rotational speed of the impeller must not exceed the specified requirements, otherwise the temperature is too high, the impeller, and the electric chance are damaged.
(3) Regularly check the safety valve to ensure safety.
ALPA Light Bagne Air Classifier Mill for Silicon Metal Case Sharing: This customer is a device company, focusing cement, mine, chemical, electric power, metallurgy, etc., mainly engaged in the solid mill used in these industries. With equipment, the customer needs to support its customers more suitable airflow classification equipment. After many exam, we have chosen our ALPA air grade machine. Buy two devices. Product particle size: D80: 15μm hour yield: two 15t / h.
Our AlPA classifier can support ball mills, vertical grinding, Raymond mill, mechanical mill, etc., welcome customers to visit, incompetent experiments.
Shan dong alpa is a scientific and technological private enterprise producing various airflow pulverations, airflow mill, medical and air flow crushers, disc air thrower, and users who need to purchase such products. Contact us.
