Steam Jet Mill for Sticky Rice

With the continuous development of pulverizer technology, Steam Jet Mill for Sticky Rice has gradually penetrated into people's daily lives.

Steam Jet Mill for Sticky Rice has the characteristics of precision, small, light, high efficiency, no dust, cleaning, easy to operate, beautiful modeling, etc., both power saving and safe. The pulverized tank and the blade are manufactured by stainless steel. It can complete the crushing and fine powder in 3 seconds - 2 minutes. It can quickly crush a variety of Chinese herbal medicines and most of the food, wide and wide, and different nature materials can be very smashed. Loss, smash different materials will not be stronger. Such as Western ginseng, ginseng, three seventh, placenta, flyer, pearl, white peony, 苡 苡 米, green beans, soy, sesame, rice, corn, etc. The host and the grading flow bearing are lipomatic lubrication, using special lipids, the replacement period of the bearing is around three months, and the filling of the grease is 1/2 of the interior space in the bearing cavity. Otherwise, It will cause too high of the bearing temperature. The spiral feeder has changed the lipid period of half a year, and Cape Calcium-based grease.

So what is the grading principle and process of Steam Jet Mill for Sticky Rice? Below, below share.

1. Open the switch in the control cabinet, start the power supply, equipment operation;

2, the raw material enters the feeder
3, the raw material enters the feeder injector in the feeder
4, the raw material reaches the hierarchical body after special dispersion, grading through physical effects such as airflow and gravity;
5, the airflow of the three flow paths has the control valve group adjustment to maintain their respective balance;
6, grading The rear coarse fine product is recovered separately;
7, clean air is discharged into the atmosphere.
For the long-term \"health\" of the equipment, we need to take some steps to protect them again.
1. First, the gap of the hammer screen can be adjusted: the friction on the screen changes varies from the distance between the material and the screen, and the friction is different. Improve the hammer speed and hammer material efficiency by adjusting the hammer net gap. However, during the production process, the screens they use are different, the raw materials are different, the hammer screening gap needs to be adjusted; in the crusher, the crusher is not very good at the beginning, but after a period of time Work, the particles inside the crusher also changes; in the grinding machine parts, the hammer head is easily worn, and the gap between the hammer head and the screen is increased, and the yield is also declining, it is difficult to maintain.

Of course, in order to test the yield of a crusher, for some of the raw materials, for some screen holes, in order to determine the appropriate hammer sieve gap and suction, the useful life of the screen and the hammer can be obtained in a short time. Very high grinding efficiency data. However, in the production of feed powder, such specific measurement dataAccording to the operator's work experience, the technical content of the crusher itself is two things. People with enrichment of experience and labor experience also require higher operating costs. When the hammer is worn, the gap between the hammer and the sieve increases, the friction is reduced, and the abrasive efficiency is lowered.

2. Steam Jet Mill for Sticky Rice mainly requires a reasonable use of reverse glitch: mainly to rush the side hair of the screen into the inside, greatly increase the friction, but this method is not used for a long time. After the globi polishing, the efficiency is lowered. It lasts for 30 minutes to 1 hour.
3. Put the friction piece into Steam Jet Mill for Sticky Rice: The friction sheet has the effect of the material ring, but the effect is limited. First, the teeth of the friction plate are in front of the hammer head, the friction surface is small, and the hammer is long-lasting; if the sieve area is too small, the output screen area will be reduced.
For any device, everyday maintenance can be performed, to ensure that the equipment can run for a long time, so daily is critical to the maintenance of Steam Jet Mill for Sticky Rice.

ALPA Carbon Steam Jet Mill for Sticky RICE Case Sharing: The company produces superfine and super fine pulverized in the production of static pressure graphite. After multi-party examinations and experiments, finally selected our AlPA as a cooperative customer, we provide the STEAM JET MILL for Sticky Rice, which is the need for carbon pulverity, particle size, yield, and other needs.
Technical parameters:
Finished granularity: D65: 200 目

Production capacity: 800-1000kg

AlPa also believes that the future airflow crushing technology will become more and better , Users who need to purchase such products can contact us.